Electronic Theatre Controls Emphasis Lighting Control System Especificaciones Pagina 345
- Pagina / 380
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Express 125/250 User Manual, v.3.1 331
Secondary Messages
Dimmer # has a load, but the recorded load is zero. Because the
recorded load is zero, the Dimmer Monitoring system is unable to
determine whether the dimmer has a load error.
The load on dimmer # has changed. Because the dimmer output is
not at a high enough level, the Dimmer Monitoring system is unable
to determine the size of the load. To correct the problem use [Check
Loads] to determine the size of the load change.
The load on dimmer # has changed from #W to #W. A decreased load
indicates lamp failure. An increased load indicates that a lamp has
been added since the last [Record Load]. Correct the problem or, to
prevent further error messages, use [Clear Load] or [Record Load].
DC output has been detected on dimmer #. If this condition persists,
it may harm the connected load. Please check the connected load.
An SCR has failed On/Off in dimmer #. The dimmer should be
replaced.
Dimmer # output has failed on. The dimmer should be replaced.
Dimmer # output has failed off. Either the circuit breaker has tripped
or the dimmer needs to be replaced.
Dimmer #'s load has failed. The most likely cause is a lamp failure.
Either replace the lamp or, to prevent further error messages, use
[Clear Load] or [Record Load].
Data error on Rack # DMX port A/B. Please check DMX cabling and
connections between the console and the rack.
Rack # ambient temperature is high at # degrees F. The temperature
does not yet exceed acceptable operational limits, but the rack
should be checked. Please check the cooling/ventilation in the
dimmer room.
Rack # ambient temperature is low at # degrees F. Please check the
heating/ventilation in the dimmer room.
Rack # ambient temperature is outside the acceptable operating
range at # degrees F. Please check the cooling/ventilation in the
dimmer room immediately.
A ground fault (GFI/RCD) error has occurred in dimmer #. Use
Dimmer status to determine the rack number for the dimmer.
The phasing in Rack # is not allowed. The rack has been shut down.
Please check the input power service.
- Contents 3
- Chapter 4 4
- Chapter 5 4
- Chapter 6 5
- Chapter 7 5
- Chapter 1 15
- Introduction 15
- Using this manual 16
- Keyboard Help 16
- Text conventions 16
- Output level conventions 18
- Enabling LTP 19
- Working with LTP channels 19
- Blocking cue 20
- Fixtures 21
- Fixture attributes 21
- Categories 21
- Personalities 21
- The Only command 22
- Using the trackpad 23
- Electronic backup maintenance 24
- Troubleshooting 24
- 12 Chapter 1 Introduction 26
- Chapter 2 27
- Monitor displays 27
- Colors in displays 28
- Display features 29
- Global settings 30
- Fader Status 30
- Cue / Time Code List 30
- Flexichannel 32
- Patch area 33
- Profile assigned 33
- Level assigned 33
- 20 Chapter 2 Monitor displays 34
- Chapter 3 35
- System settings 35
- Setting the number of dimmers 36
- Setting default fade times 38
- Setting default Level key 39
- Setting default sneak time 40
- Enable / disable Blackout key 41
- Enable / disable Flexichannel 41
- Set grandmaster type 42
- Record lockout 43
- Enable / disable bump buttons 43
- Setting the clock 44
- Daylight Savings Time 45
- Set time/date 45
- 12/24 hour clock 45
- 32 Chapter 3 System settings 46
- About Show 47
- 34 Chapter 3 System settings 48
- Patching channels 49
- Selecting one-to-one patch 50
- Creating a custom patch 51
- Proportional patching 52
- Unpatching individual dimmers 53
- Show labels 53
- Dimmer profiles 54
- Profiles display 55
- Creating or editing a profile 56
- Copying to another profile 56
- Clear All 57
- Clear to End 57
- Fill Between 57
- Resetting a profile 57
- Captured channels in Patch 58
- Dimmer check 59
- About Dimmer 60
- About Dimmer with ETCLink 61
- Setting channel levels 65
- Channel modes 66
- Channel Attributes display 67
- Independent channels 68
- Flipped channels 68
- Channel data type 69
- Channel convention 69
- Selecting channels 70
- Channel check 73
- About Channel 74
- Moving Light Functions menu 78
- Personality Setup 79
- Viewing a personality 81
- Deleting personalities 81
- Resetting defaults 81
- Patching moving lights 82
- Editing the fixture list 84
- Attribute Setup 85
- Resetting defaults: 86
- Encoder Setup 87
- Changing assignments 88
- Working with moving lights 89
- Working with fixtures 90
- Fixture focus with Solo 92
- Cue types 94
- Recording functions 95
- Viewing cues 95
- The oversized show 96
- Working with cues in Stage 97
- Recording a cue in Stage 97
- Working with cues in Blind 98
- 86 Chapter 7 Cues 100
- 88 Chapter 7 Cues 102
- 90 Chapter 7 Cues 104
- Linking a macro to a cue 105
- Recording a cue using Solo 106
- Labeling cues 107
- Modifying a recorded cue live 108
- Modifying cue attributes 109
- Updating cues 110
- Updating a recorded cue 111
- Deleting cues 112
- Copying cues 113
- Inserting cues 114
- Chapter 8 115
- Track record 116
- Recording modified cues 117
- Using Track 118
- Pulling channels in Blind 121
- Blackout cues and tracking 122
- Figure 7 123
- 110 Chapter 8 Track 124
- Chapter 9 125
- Multipart cues 125
- Recording a multipart cue 126
- Wait times in multipart cues 128
- Editing a multipart cue 129
- Using Update 130
- Modifying fade and wait times 131
- 118 Chapter 9 Multipart cues 132
- Chapter 10 133
- Playing back cues 133
- Timed faders 134
- Fader keys 135
- Cue List 136
- Fader Status display 137
- Selecting cues 137
- Playing a cue 138
- Go to a different cue 138
- Controlling fades manually 139
- Rate override 140
- Quickstep 141
- Chapter 11 143
- Recording a group in Stage 144
- Recording a group using Solo 145
- Working with groups in Blind 145
- Group Editing mode in Blind 146
- Working with groups in Stage 147
- Updating groups 148
- Updating a recorded group 149
- Labeling groups 150
- Deleting groups 151
- Copying groups 151
- 138 Chapter 11 Groups 152
- Modifying cues or submasters 153
- 140 Chapter 11 Groups 154
- Chapter 12 155
- Focus points 155
- Recording a focus point 156
- Modifying a focus point 158
- Updating focus points 159
- 146 Chapter 12 Focus points 160
- Labeling focus points 162
- Deleting focus points 163
- Copying focus points 163
- 150 Chapter 12 Focus points 164
- Chapter 13 165
- Submasters 165
- Submaster types 166
- Changing type 167
- Submaster pages 168
- Submaster bump buttons 169
- Submaster LEDs 170
- Recording submasters 171
- Adding fade and dwell times 172
- Hold dwell time 173
- Manual dwell time 173
- Adding a rate to a submaster 174
- Specifying a submaster’s page 175
- Inhibitive submasters 176
- Adding channels 177
- Deleting channels 177
- Modifying submasters in Blind 178
- Modifying submasters in Stage 178
- Updating submasters 179
- Updating a recorded submaster 180
- Labeling submasters 182
- Copying submasters 183
- Clearing submasters 184
- Chapter 14 185
- Lists and spreadsheets 185
- Submaster List 187
- Editing submasters 188
- Deleting submasters 189
- Group List 190
- Focus Point List 191
- Labeling a focus point 192
- Deleting a focus point 192
- Working in spreadsheets 193
- Creating cues 194
- Editing cues 194
- Replacing channel level 195
- Submaster spreadsheet 196
- Group spreadsheet 198
- Editing groups 199
- Focus point spreadsheet 200
- Editing focus points 201
- Deleting in spreadsheet 201
- Chapter 15 203
- Using the Park display 204
- Parking dimmers 204
- Unparking dimmers 205
- Parking channels 206
- Unparking channels 207
- Parking recorded channels 208
- Unparking recorded channels 208
- Parking fixtures 209
- Unparking fixtures 210
- Chapter 16 211
- Blind Effects display 212
- Effects in Stage 213
- Creating an effect in Blind 214
- Adding channels directly 215
- Adding groups or focus points 216
- Adding grouped channels 217
- Creating an effect in Stage 218
- Modifying the effect 221
- Editing channel levels 222
- Inserting steps 224
- Deleting steps 225
- Modifying effect attributes 226
- Effect fade times 228
- Changing upfade only 229
- Changing downfade only 229
- Changing dwell only 230
- Resetting hold dwell time 230
- Setting a random effect rate 231
- Running an effect cue 231
- Using an effect submaster 231
- 218 Chapter 16 Effects 232
- Chapter 17 233
- Subroutines 233
- Cue steps 234
- Style steps 235
- Subroutine attributes 235
- Creating subroutines 236
- Editing a subroutine 238
- Deleting a step 238
- Inserting a step 238
- Chapter 18 239
- Creating macros 240
- Using Macro Editing 242
- Macro wait 243
- Linking macros 244
- Using submasters in macros 245
- Playing macros 246
- Powerup macro 246
- Modifying macros 247
- Clearing macros 247
- Copying macros 248
- Sample macros 248
- Auto channel check 249
- Record show on disk 249
- 236 Chapter 18 Macros 250
- Chapter 19 251
- Link lists 251
- Link List overview 252
- Setting up a link 253
- Inserting a link 254
- Moving a link 255
- Merging two links 255
- Deleting a link 256
- Using a link 256
- Chapter 20 257
- Diskette functions 257
- Diskette management 258
- Formatting diskettes 258
- Contents of the showfile 259
- Writing to diskette 259
- Reading from diskette 260
- Read show components only 261
- Chapter 21 263
- Printing 263
- Printer options 264
- Printing procedure 264
- Printouts available 265
- 252 Chapter 21 Printing 266
- Chapter 22 267
- Clear functions 267
- Clear and reset procedure 268
- Clear and reset options 269
- Chapter 23 271
- Dimmer monitoring 271
- ETCLink functions 272
- Enabling ETCLink 272
- Error messages 273
- ETCLink displays 275
- Dimmer rack status 276
- Dimmer status 277
- Monitoring dimmers 278
- Record Loads procedure 279
- Load Check procedure 280
- Clear Loads procedure 281
- Setting and unsetting dimmers 282
- Recording a backup look 283
- Playing a backup look 284
- Chapter 24 285
- Control interfaces 285
- ETC MIDI 286
- ETC MIDI message formats 287
- MIDI Message definitions 288
- MIDI Show Control (MSC) 289
- Byte type 292
- Explanation 292
- Examples 293
- Real time programs 294
- Creating real time programs 296
- Referencing sunrise or sunset 297
- Referencing a date 297
- Editing real time programs 298
- Deleting real time programs 298
- Inserting real time programs 298
- Copying real time programs 299
- Moving real time programs 299
- Time Code 300
- Creating a time code program 301
- Sorting/recording events 304
- Editing time code programs 304
- Resetting loop time 305
- Deleting time code events 306
- Inserting time code events 306
- Copying time code events 307
- Moving time code events 308
- Editing events 309
- Running a time code program 311
- External time code clock 312
- Manual playback 313
- Remote macros 314
- Serial interface 314
- Remote trigger 315
- Chapter 25 317
- Accessories 317
- Remote Focus Unit (RFU) 318
- Alphanumeric keyboard 319
- Console lights 320
- Expression Off-Line 320
- Appendix A 321
- Installation 321
- Console’s back panel 322
- VGA monitor connections 323
- Understanding ETCNet 324
- Connecting dimmers to console 326
- Configuring the DMX512 ports 327
- Setting DMX512 speed 328
- Installing a printer 330
- Installing Remote Focus Unit 330
- Installing MIDI 331
- Installing console lights 331
- Installing remote macros 332
- Wiring remote macros 333
- Upgrading software 334
- 322 Appendix A Installation 336
- Appendix B 337
- References 337
- 324 Appendix B References 338
- Remote Video Interface (RVI) 339
- 326 Appendix B References 340
- Network wiring 342
- RIU jumpers 342
- RVI DIP switch settings 342
- Appendix C 343
- ETCLink errors 344
- Secondary Messages 345
- 332 Appendix C Error messages 346
- Appendix D 347
- Showfile 347
- Configuration settings 348
- Appendix E 349
- Softkeys 349
- Blind/Group 350
- Blind/Focus 350
- Blind/Submaster 350
- Blind/Cue/Effect 351
- Blind/(Cue or Sub)/Effect 351
- Blind/Submaster/Effect 351
- Blind/Subroutine 352
- Stage/Fader 352
- Stage/Park 352
- Setup - Macro Editing (8) 353
- Setup - Time Code (13) 354
- 342 Appendix E Softkeys 356
- Appendix F 357
- Time and location 357
- Appendix G 359
- Specifications 359
- Timed control 360
- Display functions 360
- Submaster functions 360
- Channel functions 361
- Moving light functions 361
- Cue functions 361
- Group functions 362
- Focus point functions 362
- Macro functions 362
- Effects functions 362
- Profile functions 363
- Size and weight 363
- 350 Appendix G Specifications 364
- Appendix H 365
- Declaration of Conformity 365
- Appendix I 367
- Limited Warranty 367
- Numerics 371
- 356 Index 372
- 358 Index 374
- 360 Index 376
- 362 Index 378
- 364 Index 380
© 2020, manymanuals.es. Todos los derechos reservados | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales